FABULAC HUB 85x(gloss level)-(colour tone)
Hesse FABULAC HUB 85x(gloss level)-(colour tone) is the HYDRO-UV Colour lacquer for all industrial applications where very good resistance is required. As a water-based and UV activated lacquer system, FABULAC sets new standards in terms of feel, durability and readiness-for-use. Application in the dual-cure procedure with the addition of hardener enables excellent opacity to be achieved in all colour ranges. FABULAC attains the following resistances: DIN 68861 1B (chemical resistance), 2D (abrasion resistance), 4E (scratch resistance).
Artikel anfragen- Elegant feel
- optimised opacity
- Good chemical and mechanical resistance
- DIN 68861 1B
- PVC-resistant
Processing
Airmix
Automatic spray gun
Airless low pressure
Areas of application
This exquisite product is used in the industry to achieve consistent lacquer surfaces in furniture, kitchen and interior door surfaces. Due to the crack-free formula, certain colour tones in the FABULAC series can also be used for panelled stairs.
Page content
Technical information
Certificates
Technical Specifications
| Appearance | opaque |
|---|---|
| Number of layers (max) | 3 |
| Quantity per layers (min) | 80 g/m² |
| Quantity per layers (max) | 130 g/m² |
| Total quantity applied | 390 g/m² |
| Mixing ratio (volumetric) | 20 : 1 |
| Mixing ratio (gravimetric) | 100 : 5 |
Processing Instructions
| Potlife | 4 h / 20 °C |
|---|---|
| Due to hardening | 7 d / 20 °C |
| Surface sanding (grain size) | 280 - 400 |
| Intermediate sanding (grain size) | 320 - 600 |
| Yield per pass | m²/l |
| Processing information | Hardener should normally be added in a slow stream while stirring; only after that should the lacquer be diluted, if necessary. Working viscosity can be adjusted with water or HYDRO Optimizer HZ 70 (maximum 3 % by volume). For strip cleaning, we recommend the HYDRO Cleaner HY 6995 at a mixing ratio of 1 : 10 with water.The specified run-out time refers to the delivery condition and may increase during storage. To adjust the run-out time for processing, the material can then be diluted with the addition of a maximum of 5% HYDRO Optimizer HZ 70 or with water. |
| Special notes | There are further alternatives to the hardener stated here. These can be found in the client-specific process description.For the white colour tones RAL 9010 and RAL 9016, it is possible to work without hardener if there is sufficient UV hardening.A long pot life of up to 5 h / 20 °C can be achieved when working with Hardener HDR 5081 at a mixing ratio (by volume) of 20 : 1.It is also possible to add Hardener HDR 5073 in a mixing ratio (by volume) of 20 : 1 prior to application. The pot life is 7 h / 20 °C, the open time is around 4 h / 20 °C.When applied to glass, the lacquer is used with hardener HDR 5040 at a mixing ratio (by volume) 10 : 1. Before lacquering, the glass must be cleaned using Hesse Cleaner HS 6601. The pot life of the material is 1 h / 20 °C. It is necessary to use a 2C system because of the short pot life. FABULAC is suitable for coating glass for low-stress, decorative purposes in non-wet areas. For glass under higher stress, we recommend using a special glass coating from the Hesse product range. This section describes the procedure for applying FABULAC on components that cannot be cured using a UV emitter due to their size: The lacquer should be configured for working viscosity by mixing it in a mixing ratio (by volume) of 20 : 1 with HYDRO Hardener HDR 5083 and with 2 - 3 % water or HYDRO Optimizer HZ 70. Application should be via cup gun or Airmix device and the application quantity should not exceed 130 g/m². The pot life is 3 h / 20 °C, with drying in a trolley for 16 h / 20 °C. This application method is advisable for large components like cornices for which a chemical resistance to DIN 68861-1C is sufficient. Please conduct a test of the bond on the substrate being used. |
Procedure example
Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.
Request a series
<% headline %>
Your request for the article
FABULAC HUB 85x(gloss level)-(colour tone)Your request for the series
FABULAC HUB 85x(gloss level)-(colour tone)
